Fluke Corporation                                           MET/CAL Procedure
=============================================================================
INSTRUMENT:            Fluke 8024B: CAL ADJ /5100
DATE:                  10-Feb-95
AUTHOR:                Fluke Corporation
REVISION:              $Revision: 2.3 $
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       1
NUMBER OF LINES:       77
CONFIGURATION:         Fluke 5100B
=============================================================================
#
# Source:
#   Fluke 8024B instruction manual (PN 616052 July 1981).
#
# Compatibility:
#   MET/CAL 3.0 or later
#
# Subprocedures:
#   None
#
# Required Files:
#   None
#
# System Specifications:
#   TUR calculation is based on specification interval of the accuracy file.
#   The default 5100B accuracy file contains 6 month specs.
#
# Fluke makes no warranty, expressed or implied, as to the fitness
# or suitability of this procedure in the customer's application.
#
# The 6 month specifications of the 5100B are used in TUR computations.
#
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-                                                              W
  1.002  HEAD         EQUIPMENT SETUP
  1.003  DISP         Ambient temperature: 21C - 25C.
  1.003  DISP         Relative humidity: less than 80%.
  1.003  DISP         Allow the UUT 30 min. to stabilize.
  1.004  HEAD         CALIBRATION ACCESS PROCEDURE
  1.005  DISP         Disconnect the test leads and the battery eliminator
  1.005  DISP         if attached. Open the battery compartment, and
  1.005  DISP         disconnect the battery. Remove the three phillips-head
  1.005  DISP         screws from the bottom of the case. Turn the instrument
  1.005  DISP         face-up, and grasp the top cover at both sides of the
  1.005  DISP         input connectors. Then, pull the top cover from the UUT.
  1.006  DISP         Reconnect the battery and turn the UUT on.
  1.007  HEAD         DC VOLTAGE CALIBRATION ADJUSTMENT
  1.008  DISP         Connect the 5100B and UUT as follows:
  1.008  DISP         [32] 5100B OUTPUT HI to UUT V Ohm S
  1.008  DISP         [32] 5100B OUTPUT LO to UUT COMMON
  1.009  RNG          200mV
  1.010  5100         190mV                                             S  2W
  1.011  DISP         Adjust R6 for a display of 190.0 exactly.
  1.012  DISP         Connect a Jumper wire across Q10 and push
  1.012  DISP         the PEAK HOLD switch to the ON position.
  1.013  DISP         Adjust R17 (PEAK HOLD) for a display of 190.0 exactly.
  1.014  DISP         Remove the Jumper wire from Q10. Push PEAK HOLD to OFF.
  1.015  5100         *                                                 S
  1.016  HEAD         AC VOLTAGE CALIBRATION ADJUSTMENT
  1.017  RNG          200mV                        AC
  1.018  5100         190mV                        100H                 S  2W
  1.019  DISP         Adjust R4 for a display of 190.0mV exactly.
  1.020  5100         *                                                 S
  1.021  RNG          2V                           AC
  1.022  5100         1.9V                         5kH                  S  2W
  1.023  DISP         Adjust C1 for a display of 1.900V (+/-95counts).
  1.024  5100         *                                                 S
  1.025  HEAD         TEMPERATURE CALIBRATION ADJUSTMENT
  1.026  DISP         Establish a lag bath (ice point environment) as
  1.026  DISP         shown in figure 4-6 of the 8024B manual. Allow
  1.026  DISP         the lag bath to stabilize for 30 minutes (to reach
  1.026  DISP         thermal equilibrium).
  1.027  DISP         Connect the thermocouple accessory to the UUT.
  1.028  DISP         Adjust the TEMP CAL (R10) for a UUT reading equal to
  1.028  DISP         the Temperature Reference Monitor reading.
  1.029  END